BIOGEAR XP 460
REAL Protection

BIOGEAR XP 460

Seal of ApprovalThe Environmentally Acceptable Gear Lubricant delivering superior anti-wear, EP and oxidation protection even under severe conditions

  • Exceeds the requirements of DIN 51517 part 3
  • Excellent equipment protection
  • Superior thermal stability
  • ISO 68, 100, 150, 220, 320 and 460

For thrusters, some CPP designs and deck equipment

 

BIOGEAR XP 460 – AT A GLANCE
Attribute Test Result
Wear Protection FZG > Load stage 14
Micropitting Passes all 5 endurance stages
FE8 Pass
Corrosion Protection ASTM D130 Copper Corrosion Pass
ASTM D665 Rust (Fresh and Sea Water) Pass
Elastomer Compatibility NBR, HNBR, FKM, PTFE, PU80, PU90 Pass
Gear Standards DIN 51517 part 3 (2018) Pass
ANSI/AGMA 9005-F16 Pass
VGP Compliant

 

Sanmar-Rascal-1800-VZ900-19A-1700mm-(10)BIOGEAR XP is a range of biodegradable, high performance, extreme pressure (EP) gear lubricants with excellent anti-wear and micropitting performance, available in ISO 68, 100, 150, 220, 320 and 460 viscosities. These lubricants are based on fully saturated synthetic esters with a high degree of renewability and use state-of-the art technology.

BIOGEAR XP is designed for use in sensitive environments where there is a potential for fluid loss to occur, for example from thrusters, some CPP designs and deck equipment.

BIOGEAR XP is miscible with common mineral based gear oils, but in line with good practice, old lubricants should be drained completely to avoid any risk of additive incompatibility and ensure that the full benefits and performance are achieved. Water content should not exceed 0.1% and any free water must be separated off on a regular basis. Unlike the HYDROX range, these lubricants do not emulsify in water.

BIOGEAR XP achieves a biodegradability of greater than 60% in the 28 day OECD 301B test. These products are considered non-toxic in the marine environment based on the following results:

FISH DAPHNIA ALGAE
LC50 exceeds 100 mg/l EC50 exceeds 100 mg/l EC50 excedes 100 mg/l

BIOGEAR XP meets the detailed ecological definitions and requirements laid down in the 2013 Vessel General Permit (VGP) published by the US EPA in March 2013.

Attribute Benefit
Extended fluid life Fewer fluid changes, less equipment downtime and lower overall cost of ownership
Excellent resistance to micropitting Protects the gear teeth against fatigue wear resulting in less down time
High EP protection Ability to withstand shock and high loads
Excellent water separation Enables easy removal of free water
Good hydrolytic stability Resists breakdown of the lubricant by water in high temperature situations
Wider operating temperatures Protects equipment from -25ºC to over +100ºC
Superior oxidative stability Less sludge and system failures, longer fluid life and less fluid thickening
Good elastomer compatibility Compatible with most sealing materials including Nitrile and Viton
Biodegradable and minimally toxic Lower environmental risk

Photographs supplied courtesy of Veth Propulsion

Safety Data Sheets

This section of the website requires registration

Please log-in


Forgot your password or username?

Reset your password here


Not registered?

Please complete the registration from below if you do not have an account with us.

Register

  • Lower case letters and numbers only
  • Please ensure you enter an email address that you can access. An activation email will be sent to this address when you submit the form.
  • Your information

    This form collects and stores your information so we can create your account enabling you to access our Safety Data Sheet (SDS) Records. Please read our Privacy Policy for more information about how we manage your data.

  • This field is for validation purposes and should be left unchanged.